2021 RV and tow vehicle recalls

The spare tire carrier bracket may experience metal fatigue and break, allowing the spare tire to detach from the trailer.

Campaign page2021 Airstream Basecamp

The 12-gauge wire for future air conditioner installation was not properly terminated inside the junction box.

Campaign page2021 Airstream Basecamp

The internal aluminum burner tubes that connect to the gas valves may fracture and cause a gas leak.

Campaign page2021 Airstream Basecamp

The adhesive bond between the glass and metal frame of the entry door window can fail, causing the glass to separate from the frame.

Campaign page2021 Airstream Basecamp

The burner control valves may become damaged, causing a gas leak.

Campaign page2021 Airstream Basecamp

The information printed on the Federal Certification and Tire Placard is 255/55R18 - 50 PSI, when the correct information is ST225/75R15E - 80 PSI. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims" and 567, "Certification.”

Campaign page2021 Airstream Basecamp

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Airstream Flying Cloud

The stove top range was incorrectly installed in a non-sealed cabinet.

Campaign page2021 Airstream Flying Cloud

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Airstream Globetrotter

The adhesive on the overhead cabinet doors may fail.

Campaign page2021 Airstream Globetrotter

The burner control valves may become damaged, causing a gas leak.

Campaign page2021 Airstream Interstate Nineteen

The buss bar circuit breaker may have been incorrectly wired.

Campaign page2021 Airstream Interstate Nineteen

A wire connector from the solar panel ports to the solar charge lines may loosen.

Campaign page2021 Alliance RV Paradigm

A wire connector from the solar panel ports to the solar charge lines may loosen.

Campaign page2021 Alliance RV Valor

The transmission control valve may fail and cause the rear wheels to lock-up.

Campaign page2021 Chevrolet Silverado 2500

The tailgate's electronic gate-release switch may short circuit due to water intrusion, which can result in the tailgate inadvertently unlatching while the vehicle is in park.

Campaign page2021 Chevrolet Silverado 2500

The bolts that attach the brake pressure modulator valve (BPMV) assembly may not be properly tightened, which could fail to seal the two sub-assemblies and allow water intrusion.

Campaign page2021 Chevrolet Silverado 2500

Operating the spare tire with other 20" or 18" tires can prevent the Anti-Lock Braking System (ABS) from engaging.

Campaign page2021 Chevrolet Silverado 2500

Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.

Campaign page2021 Chevrolet Silverado 2500

The seat belt brackets may not be secured to the seat frame in the front-row center seating position.

Campaign page2021 Chevrolet Silverado 2500

The transmission control valve may fail and cause the rear wheels to lock-up.

Campaign page2021 Chevrolet Silverado 3500

The tailgate's electronic gate-release switch may short circuit due to water intrusion, which can result in the tailgate inadvertently unlatching while the vehicle is in park.

Campaign page2021 Chevrolet Silverado 3500

The bolts that attach the brake pressure modulator valve (BPMV) assembly may not be properly tightened, which could fail to seal the two sub-assemblies and allow water intrusion.

Campaign page2021 Chevrolet Silverado 3500

Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.

Campaign page2021 Chevrolet Silverado 3500

The seat belt brackets may not be secured to the seat frame in the front-row center seating position.

Campaign page2021 Chevrolet Silverado 3500

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Coachmen Apex

The cooktop may not be isolated properly from the furnace return air, which can cause the flame to become inverted.

Campaign page2021 Coachmen Clipper

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Coachmen Freedom Express

The retractable awning may extend unintentionally during transit.

Campaign page2021 Coachmen Nova

The fuel hose between the inline fuel filter and the Injection Pump Module (IPM) may have inadequate clamp force, possibly resulting in a gasoline leak.

Campaign page2021 Coachmen Nova

The burner control valves may become damaged, causing a gas leak.

Campaign page2021 Coachmen Nova

The Absorbed Glass Mat (AGM) battery was incorrectly installed inside the vehicle, which can allow hydrogen gas to enter the vehicle.

Campaign page2021 Coachmen Nova

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Coachmen Spirit

The service valves on the LPG tanks may be improperly connected, which can cause a propane leak.

Campaign page2021 Coachmen Sportscoach

The outdoor cooktop can be stowed with the propane hose connected.

Campaign page2021 Coachmen Sportscoach

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Coachmen Sportscoach

The P2K Bunk Bed System motor may fail, causing the bunk to fall from the stowed position.

Campaign page2021 Coachmen Sportscoach

The trailers may be equipped with axle springs rated at 4400 pounds instead of 5100 pounds.

Campaign page2021 Dutchmen Coleman

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Dutchmen Coleman

The U-bolts on the axles may have been improperly tightened, causing the bolts to loosen and the axle to slide.

Campaign page2021 Dutchmen Voltage

The Federal Identification Tag incorrectly lists the recommended tire pressure as 95 PSI, instead of the correct tire pressure of 110 PSI. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification."

Campaign page2021 Dutchmen Voltage

The Federal Identification Tag incorrectly lists the recommended tire pressure as 110 PSI, instead of the correct tire pressure of 95 PSI. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification."

Campaign page2021 Dutchmen Voltage

The air conditioner soft start device may fail and overheat.

Campaign page2021 Dynamax Isata

The LED backlight circuit board in the cooktop range may fail, causing the board to overheat.

Campaign page2021 Dynamax Isata

The service valves on the LPG tanks may be improperly connected, which can cause a propane leak.

Campaign page2021 Dynamax Isata

Inadequate warmup protection can cause a lack of oil film on the engine connecting rod bearings while the engine is reaching operating temperature. This can result in engine damage and connecting rod failure, which could potentially puncture the engine block.

Campaign page2021 Dynamax Isata

The wiring harnesses for the front seats may have been routed incorrectly and could become jammed and damaged in the swivel seat frames.

Campaign page2021 Dynamax Isata

The rear part of the front fender liner may contact and chafe the brake hose, possibly resulting in a loss of brake fluid.

Campaign page2021 Dynamax Isata

The operator's manual does not correctly specify certain conditions under which the automatic parking function ("Auto-P") operates.

Campaign page2021 Dynamax Isata

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 East to West Alta

The LP/CO detector was installed in the incorrect location.

Campaign page2021 East to West Alta

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 East to West Silver Lake

The outdoor grill may be able to be stowed away while the propane hose is still attached and while the burners are on.

Campaign page2021 East to West Silver Lake

The windshield wipers may fail, resulting in reduced driver visibility.

Campaign page2021 Entegra Accolade

The tire valve stem extension for the inner wheel may come into contact with the outer wheel rim opening and become damaged.

Campaign page2021 Entegra Accolade

The steering arm and tie rod bolts may have a defective seam that can fracture.

Campaign page2021 Entegra Accolade

The tie rod clamps may be loose, which could result in loose tie rod ends that could break or detach.

Campaign page2021 Entegra Accolade

The pedestal mounting plate on the passenger's seat may be improperly welded, causing the plate to separate and the seat assembly to loosen or detach. As such, these seat assemblies fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems" and number 210, "Seat belt assembly anchorages."

Campaign page2021 Entegra Aspire

The engine air intake box may not have a water drain installed, which can cause water to build up inside the air intake box.

Campaign page2021 Entegra Aspire

The instrument cluster may intermittently go blank while the vehicle is in motion.

Campaign page2021 Entegra Aspire

A fuel leak may occur in the fuel hoses between the fuel pump and the remote fuel filter head.

Campaign page2021 Entegra Aspire

The sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak.

Campaign page2021 Entegra Aspire

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Entegra Aspire

The power seat wiring may become chafed due to poor routing, and no protection, or melt from exceeding the 14 gauge wire amp capacity.

Campaign page2021 Entegra Aspire

The pedestal mounting plate on the passenger's seat may be improperly welded, causing the plate to separate and the seat assembly to loosen or detach. As such, these seat assemblies fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems" and number 210, "Seat belt assembly anchorages."

Campaign page2021 Entegra Cornerstone

The engine air intake box may not have a water drain installed, which can cause water to build up inside the air intake box.

Campaign page2021 Entegra Cornerstone

A machining defect may cause pressure to build in the power steering pump and break the shaft seal, resulting in a loss of power steering assist.

Campaign page2021 Entegra Cornerstone

The instrument cluster may intermittently go blank while the vehicle is in motion.

Campaign page2021 Entegra Cornerstone

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Entegra Cornerstone

The power seat wiring may become chafed due to poor routing, and no protection, or melt from exceeding the 14 gauge wire amp capacity.

Campaign page2021 Entegra Cornerstone

An inadequate connection between the power steering pressure line and the brake hydroboost unit may result in a sudden loss of power steering fluid.

Campaign page2021 Entegra Esteem

An inadequate connection between the power steering pressure line and the brake Hydroboost unit may result in a sudden loss of power steering fluid.

Campaign page2021 Entegra Esteem

The mounting brackets for the leveling system hydraulic pump and reservoir may fail, allowing the components to contact the ground.

Campaign page2021 Entegra Esteem

An inadequate connection between the power steering pressure line and the brake hydroboost unit may result in a sudden loss of power steering fluid.

Campaign page2021 Entegra Odyssey

An inadequate connection between the power steering pressure line and the brake Hydroboost unit may result in a sudden loss of power steering fluid.

Campaign page2021 Entegra Odyssey

The mounting brackets for the leveling system hydraulic pump and reservoir may fail, allowing the components to contact the ground.

Campaign page2021 Entegra Odyssey

The rear stabilizer bar attachment brackets may break and separate from the vehicle.

Campaign page2021 Entegra Vision

The engine covers may not contain sufficient heat insulation, causing the interior surface temperatures to be excessive.

Campaign page2021 Entegra Vision

Biodiesel deposits may form on the pump drivetrain roller components, which could lead to failure of the high pressure fuel pump.

Campaign page2021 Ford F-250 SD

The 360-degree view camera system may not display a rearview image properly in certain lighting conditions.

Campaign page2021 Ford F-250 SD

The steering column upper shaft may detach from the steering column and result in a loss of steering control.

Campaign page2021 Ford F-250 SD

The low-pressure fuel pump may fail, which can result in an engine stall while driving.

Campaign page2021 Ford F-250 SD

A software error may cause the rearview camera to display a blank image, or the image may remain on the display after the backing event has ended.

Campaign page2021 Ford F-250 SD

The rearview camera may display a blank or distorted image.

Campaign page2021 Ford F-250 SD

Biodiesel deposits may form on the pump drivetrain roller components, which could lead to failure of the high pressure fuel pump.

Campaign page2021 Ford F-250 SD

The owner's manual does not include instructions for adjusting or removing certain head restraints. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 202, "Head Restraints."

Campaign page2021 Ford F-250 SD

The windshield wiper arms may break, causing the windshield wipers to fail.

Campaign page2021 Ford F-250 SD

Underbody heat and noise insulators may loosen and contact the aluminum driveshaft, which could damage the driveshaft and cause it to fracture.

Campaign page2021 Ford F-250 SD

A small void may be present in the top-center of the vehicle's underhood secondary fuel filter cap, which may progress to a pinhole over time, allowing fuel to leak from the top of the secondary fuel filter.

Campaign page2021 Ford F-250 SD

During manufacturing, the windshield may not have been properly bonded to the vehicle, allowing it to detach in a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 212, "Windshield Mounting."

Campaign page2021 Ford F-250 SD

The kits were sold as an accessory for certain 2005-2021 Ford F-250 4X4 and F-350 4X4 pickup trucks. The foam ring inside the stabilizer "through shaft" may block the piston ports, possibly causing the steering to lock up.

Campaign page2021 Ford F-250 SD

Biodiesel deposits may form on the pump drivetrain roller components, which could lead to failure of the high pressure fuel pump.

Campaign page2021 Ford F-350 SD

The 360-degree view camera system may not display a rearview image properly in certain lighting conditions.

Campaign page2021 Ford F-350 SD

The steering column upper shaft may detach from the steering column and result in a loss of steering control.

Campaign page2021 Ford F-350 SD

The low-pressure fuel pump may fail, which can result in an engine stall while driving.

Campaign page2021 Ford F-350 SD

The rearview camera may display a blank or distorted image.

Campaign page2021 Ford F-350 SD

Biodiesel deposits may form on the pump drivetrain roller components, which could lead to failure of the high pressure fuel pump.

Campaign page2021 Ford F-350 SD

The owner's manual does not include instructions for adjusting or removing certain head restraints. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 202, "Head Restraints."

Campaign page2021 Ford F-350 SD

The windshield wiper arms may break, causing the windshield wipers to fail.

Campaign page2021 Ford F-350 SD

Underbody heat and noise insulators may loosen and contact the aluminum driveshaft, which could damage the driveshaft and cause it to fracture.

Campaign page2021 Ford F-350 SD

A small void may be present in the top-center of the vehicle's underhood secondary fuel filter cap, which may progress to a pinhole over time, allowing fuel to leak from the top of the secondary fuel filter.

Campaign page2021 Ford F-350 SD

The rear axle housing may not support the load of the pickup truck and deform, which could result in driveshaft separation.

Campaign page2021 Ford F-350 SD

The front wheel hub extenders may be improperly attached to the front rotor hub assemblies, which could result in separation of the wheels and wheel extenders from the vehicle.

Campaign page2021 Ford F-350 SD

Ford Motor Company (Ford) is recalling certain 2021 Super Duty F-350 and F-450 vehicles equipped with a fifth wheel left-hand mounting bracket that may be cracked.

Campaign page2021 Ford F-350 SD

During manufacturing, the windshield may not have been properly bonded to the vehicle, allowing it to detach in a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 212, "Windshield Mounting."

Campaign page2021 Ford F-350 SD

The kits were sold as an accessory for certain 2005-2021 Ford F-250 4X4 and F-350 4X4 pickup trucks. The foam ring inside the stabilizer "through shaft" may block the piston ports, possibly causing the steering to lock up.

Campaign page2021 Ford F-350 SD

The Gross Vehicle Weight Rating (GVWR) on the Federal placard may exceed the safety chain rating. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) numbers 110, "Tire Selection and Rims" and 120, "Wheels and Rims - Other Than Passenger Cars."

Campaign page2021 Forest River Aurora

The breakaway switch may be incorrectly wired to the battery disconnect, which can prevent the trailer brakes from activating as intended.

Campaign page2021 Forest River Aurora

The panel that isolates the cooktop from the furnace was not properly sealed during manufacturing, which could result in an inverted cooktop flame.

Campaign page2021 Forest River Aurora

The retractable awning may extend unintentionally during transit.

Campaign page2021 Forest River Berkshire

An incorrect circuit breaker was installed in the vehicle's house distribution subpanel, which prohibits the internal spring retention mechanism from properly contacting the subpanel.

Campaign page2021 Forest River Berkshire

These vehicles may have been manufactured with unsealed 5-AMP and 20-AMP mini-breakers, which could cause a spark in the battery compartment.

Campaign page2021 Forest River Berkshire

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Forest River Berkshire

The brake lights may not adequately reflect light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

Campaign page2021 Forest River Berkshire

The saddle valve securing bolt may be overtightened, possibly damaging the o-ring seal and causing a continuous gas leak.

Campaign page2021 Forest River Berkshire

The tire valve stem extension for the inner wheel may come in contact with the outer wheel rim opening and become damaged.

Campaign page2021 Forest River Berkshire

These inverters supply too much current to the 10 gauge Romex wire.

Campaign page2021 Forest River Berkshire

The LED backlight circuit board in the cooktop range may fail, causing the board to overheat.

Campaign page2021 Forest River Cardinal

Due to a manufacturing issue, the tires may experience a belt separation.

Campaign page2021 Forest River Cardinal

The generator compartment may not be sealed properly, allowing carbon monoxide to enter the vehicle.

Campaign page2021 Forest River Cardinal

The spare tire carrier may be installed incorrectly, allowing it to detach from the vehicle.

Campaign page2021 Forest River Cardinal

The furnace flue may become misaligned due to insufficient furnace hold screws that allow movement during travel.

Campaign page2021 Forest River Cardinal

The fresh air intake sleeve for the furnace is too short and does not have proper connection of the furnace to the exterior, allowing furnace exhaust to enter the trailer.

Campaign page2021 Forest River Cardinal

The overcurrent protection from the trailer battery may have been incorrectly routed, allowing the wires to be pulled out of the junction box.

Campaign page2021 Forest River Cedar Creek

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Cedar Creek

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Cherokee

The tire size and Gross Axle Weight Rating (GAWR) on the Federal Placard are incorrect, which could result in the vehicle being overloaded. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims" and 49 CFR Part 567, "Certification."

Campaign page2021 Forest River Cherokee

The shore cord inlet wiring insulation may not have been sufficiently stripped back, causing a poor connection with the set screw.

Campaign page2021 Forest River Cherokee

The propane gas line may be routed around sharp edges which may cause a propane leak.

Campaign page2021 Forest River Cherokee Wolf Pack

The Breakaway switch power lead is wired incorrectly and may lose power.

Campaign page2021 Forest River Coachmen

The LED backlight circuit board in the cooktop range may fail, causing the board to overheat.

Campaign page2021 Forest River Columbus

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Columbus

The breakaway switch and trailer brakes may not activate when needed due to an incorrectly wired breakaway switch.

Campaign page2021 Forest River Columbus

The legs on the Allure Swivel Dining chair may detach from the chair body.

Campaign page2021 Forest River Columbus

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Flagstaff

The pin box may be under-rated for the Gross Vehicle Weight Rating (GVWR) of the vehicle.

Campaign page2021 Forest River Flagstaff

The fuel hose between the inline fuel filter and the Injection Pump Module (IPM) may have inadequate clamp force, possibly resulting in a gasoline leak.

Campaign page2021 Forest River Forester

The solar panel mounting hardware may become loose and pull through the slot in the panel.

Campaign page2021 Forest River Forester

The wiring harnesses for the front seats may have been routed incorrectly and could become jammed and damaged in the swivel seat frames.

Campaign page2021 Forest River Forester

The rear part of the front fender liner may contact and chafe the brake hose, possibly resulting in a loss of brake fluid.

Campaign page2021 Forest River Forester

The operator's manual does not correctly specify certain conditions under which the automatic parking function ("Auto-P") operates.

Campaign page2021 Forest River Forester

The liquid petroleum gas (LPG) tank mounting brackets may break, which can result in the LPG tank becoming dislodged and damaged.

Campaign page2021 Forest River FR3

The solar panel mounting hardware may become loose and pull through the slot in the panel.

Campaign page2021 Forest River FR3

The wiring harness may have an incorrect wire connected to the parking brake, allowing the leveling jacks to deploy inadvertently while the vehicle is in motion.

Campaign page2021 Forest River FR3

The liquid petroleum gas (LPG) tank mounting brackets may break, which can result in the LPG tank becoming dislodged and damaged.

Campaign page2021 Forest River Georgetown

The solar panel mounting hardware may become loose and pull through the slot in the panel.

Campaign page2021 Forest River Georgetown

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Forest River Georgetown

The P2K Bunk Bed System motor may fail, causing the bunk to fall from the stowed position.

Campaign page2021 Forest River Georgetown

The LED backlight circuit board in the cooktop range may fail, causing the board to overheat.

Campaign page2021 Forest River Ibex

The shackle nuts may have been insufficiently tightened during production.

Campaign page2021 Forest River Ibex

The solar charge line, front LED hitch light, and the pass-thru light may have been wired to the incorrect mini breaker.

Campaign page2021 Forest River Impression

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Impression

The center identification light on the rear of the vehicle was incorrectly installed at a higher position than the other lights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Campaign page2021 Forest River Impression

The fresh water tank may dislodge from the vehicle and fall to the ground when full or overfilled.

Campaign page2021 Forest River Ozark

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Ozark

The antenna wing may not be properly secured to the roof, allowing it to detach from the roof while moving.

Campaign page2021 Forest River Palomino

The overcurrent protection from the trailer battery may have been incorrectly routed, allowing the wires to be pulled out of the junction box.

Campaign page2021 Forest River Puma

The black wastewater-holding tank may be missing the ventilation pipe, allowing methane gas to build up.

Campaign page2021 Forest River Puma

The outdoor cooktop may be stowed away while the propane hose is still attached and the burner is on.

Campaign page2021 Forest River Puma

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Rockwood

The pin box may be under-rated for the Gross Vehicle Weight Rating (GVWR) of the vehicle.

Campaign page2021 Forest River Rockwood

The Federal Placard indicates an incorrect Gross Axle Weight Rating (GAWR).

Campaign page2021 Forest River Rockwood

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Sabre

The distribution panel wire may be connected to the battery without over current protection.

Campaign page2021 Forest River Salem

The fresh water tank may dislodge from the vehicle and fall to the ground when full or overfilled.

Campaign page2021 Forest River Salem

The awning rail may not be attached to a backer in the sidewall, which can allow the awning to detach while the vehicle is in motion.

Campaign page2021 Forest River Salem

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Salem

The Federal Placard lists a Gross Vehicle Weight Rating (GVWR) that exceeds the load carrying capacity of the pin box, which could result in an overloaded pin box.

Campaign page2021 Forest River Salem

The fresh water tank may not be properly secured to the vehicle's frame.

Campaign page2021 Forest River Salem

The red and amber clearance lamps do not reflect enough light. As such these vehicles fail to comply with Federal Motor Vehicle Safety Standards (FMVSS) number 108, "Lamps, Reflective Devices, and Assoc.

Campaign page2021 Forest River Salem

The flame on the cooktop may become inverted, due to the cooktop not being isolated from the furnace return air.

Campaign page2021 Forest River Salem

The break-away safety switch may not be wired to constant power, which can cause the trailer brakes to not activate in the event of a trailer separation from the tow vehicle.

Campaign page2021 Forest River Salem

The fresh water tank may not be properly secured to the vehicle's frame.

Campaign page2021 Forest River Salem

The bolts that hold the floor to the chassis were improperly tightened.

Campaign page2021 Forest River Sandpiper

The bolts that hold the floor to the chassis were improperly tightened.

Campaign page2021 Forest River Sierra

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Stealth

The fuel hose between the inline fuel filter and the Injection Pump Module (IPM) may have inadequate clamp force, possibly resulting in a gasoline leak.

Campaign page2021 Forest River Sunseeker

The wiring harnesses for the front seats may have been routed incorrectly and could become jammed and damaged in the swivel seat frames.

Campaign page2021 Forest River Sunseeker

The rear part of the front fender liner may contact and chafe the brake hose, possibly resulting in a loss of brake fluid.

Campaign page2021 Forest River Sunseeker

The operator's manual does not correctly specify certain conditions under which the automatic parking function ("Auto-P") operates.

Campaign page2021 Forest River Sunseeker

The safety chains are insufficient for the trailer's Gross Vehicle Weight Rating (GVWR) and may break in the event of the trailer coming unhitched.

Campaign page2021 Forest River Surveyor

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Vengeance

The fifth-wheel landing legs may not be seated properly with enough space between the brackets which are welded to the chassis, allowing the fifth wheel to slip down the landing leg and can puncture the floor of the vehicle.

Campaign page2021 Forest River Vengeance

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Vibe

The roof vent for the refrigerator may be missing.

Campaign page2021 Forest River Vibe

The distribution panel wire may be connected to the battery without over current protection.

Campaign page2021 Forest River Wildwood

The fresh water tank may dislodge from the vehicle and fall to the ground when full or overfilled.

Campaign page2021 Forest River Wildwood

The awning rail may not be attached to a backer in the sidewall, which can allow the awning to detach while the vehicle is in motion.

Campaign page2021 Forest River Wildwood

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River Wildwood

The Federal Placard lists a Gross Vehicle Weight Rating (GVWR) that exceeds the load carrying capacity of the pin box, which could result in an overloaded pin box.

Campaign page2021 Forest River Wildwood

The fresh water tank may not be properly secured to the vehicle's frame.

Campaign page2021 Forest River Wildwood

The red and amber clearance lamps do not reflect enough light. As such these vehicles fail to comply with Federal Motor Vehicle Safety Standards (FMVSS) number 108, "Lamps, Reflective Devices, and Assoc.

Campaign page2021 Forest River Wildwood

The flame on the cooktop may become inverted, due to the cooktop not being isolated from the furnace return air.

Campaign page2021 Forest River Wildwood

The break-away safety switch may not be wired to constant power, which can cause the trailer brakes to not activate in the event of a trailer separation from the tow vehicle.

Campaign page2021 Forest River Wildwood

The fresh water tank may not be properly secured to the vehicle's frame.

Campaign page2021 Forest River Wildwood

The side marker lights may not reflect light as intended, which can make it difficult for other drivers to see the trailer. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Campaign page2021 Forest River Work And Play

The mounting brackets may be improperly located or secured, allowing the fresh water tank to detach when full.

Campaign page2021 Forest River XLR Toyhauler

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Forest River XLR Toyhauler

The protective panel that separates the furnace and furnace components from the mid-deck cargo area is missing.

Campaign page2021 Forest River XLR Toyhauler

The Federal Placard and Cargo Carrying Capacity (CCC) label may state a lower weight than the actual weight. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 120, "Wheels and Rims-Other Than Passenger Cars."

Campaign page2021 Forest River XLR Toyhauler

The transmission control valve may fail and cause the rear wheels to lock-up.

Campaign page2021 GMC Sierra 2500

The tailgate's electronic gate-release switch may short circuit due to water intrusion, which can result in the tailgate inadvertently unlatching while the vehicle is in park.

Campaign page2021 GMC Sierra 2500

The bolts that attach the brake pressure modulator valve (BPMV) assembly may not be properly tightened, which could fail to seal the two sub-assemblies and allow water intrusion.

Campaign page2021 GMC Sierra 2500

Operating the spare tire with other 20" or 18" tires can prevent the Anti-Lock Braking System (ABS) from engaging.

Campaign page2021 GMC Sierra 2500

Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.

Campaign page2021 GMC Sierra 2500

The seat belt brackets may not be secured to the seat frame in the front-row center seating position.

Campaign page2021 GMC Sierra 2500

The transmission control valve may fail and cause the rear wheels to lock-up.

Campaign page2021 GMC Sierra 3500

The tailgate's electronic gate-release switch may short circuit due to water intrusion, which can result in the tailgate inadvertently unlatching while the vehicle is in park.

Campaign page2021 GMC Sierra 3500

The bolts that attach the brake pressure modulator valve (BPMV) assembly may not be properly tightened, which could fail to seal the two sub-assemblies and allow water intrusion.

Campaign page2021 GMC Sierra 3500

Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.

Campaign page2021 GMC Sierra 3500

The seat belt brackets may not be secured to the seat frame in the front-row center seating position.

Campaign page2021 GMC Sierra 3500

The cast aluminum pull handles on the cabinet doors and drawers may have sharp edges.

Campaign page2021 Grand Design Imagine

The axles may have been assembled with incorrect inner bearings.

Campaign page2021 Grand Design Imagine

The LP regulator that controls the LP gas pressure may fail, allowing excessive gas pressure that causes the appliance flame to increase.

Campaign page2021 Grand Design Imagine

The U-bolt may become loose due to inadequate preload and preload losses, causing the axle to move out of position.

Campaign page2021 Grand Design Momentum

The U-bolts may have been improperly tightened, which can cause the axle to move out of position.

Campaign page2021 Grand Design Momentum

A 110-volt wire in the refrigerator cabinet may be improperly secured, which could result in the wire contacting the refrigerator cooling unit, causing an electrical arc.

Campaign page2021 Grand Design Momentum

The LP regulator that controls the LP gas pressure may fail, allowing excessive gas pressure that causes the appliance flame to increase.

Campaign page2021 Grand Design Momentum

A 110-volt wire in the refrigerator cabinet may be improperly secured, which could result in the wire contacting the refrigerator cooling unit, causing an electrical arc.

Campaign page2021 Grand Design Reflection

The step tread joints may be unsupported, causing the tread to break.

Campaign page2021 Grand Design Solitude

The U-bolts may have been improperly tightened, which can cause the axle to move out of position.

Campaign page2021 Grand Design Solitude

A 110-volt wire in the refrigerator cabinet may be improperly secured, which could result in the wire contacting the refrigerator cooling unit, causing an electrical arc.

Campaign page2021 Grand Design Solitude

The liquid propane (LP) supply line that runs through the exterior lower refrigerator compartment may contact the burner tube of the refrigerator, possibly damaging the line and causing an LP gas leak.

Campaign page2021 Grand Design Solitude

Due to a manufacturing issue, the tires may experience a belt separation.

Campaign page2021 Heartland Cyclone

The transfer switch wire securement lugs may have been improperly tightened during production, causing the wires to come loose.

Campaign page2021 Heartland Cyclone

Due to insufficient bracing, the front landing legs may buckle and collapse while the trailer is parked.

Campaign page2021 Heartland Cyclone

The refrigerator roof vents were not routed properly during production.

Campaign page2021 Heartland Mallard

The LP gas lines may not have been tightened properly on the outside cooktops, which could result in a gas leak.

Campaign page2021 Heartland Mallard

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Heartland Mallard

These units had incorrect axle, rims, and tires installed during production.

Campaign page2021 Heartland Mallard

The liquid propane (LP) hose and connector may contact the suspension shackle.

Campaign page2021 Heartland Mallard

The rear stabilizer bar attachment brackets may break and separate from the vehicle.

Campaign page2021 Jayco Alante

The engine covers may not contain sufficient heat insulation, causing the interior surface temperatures to be excessive.

Campaign page2021 Jayco Alante

The bedlift motor may fail due to internal gear failure, causing the overhead bunk bed to release from the stowed position.

Campaign page2021 Jayco Alante

An inadequate connection between the power steering pressure line and the brake hydroboost unit may result in a sudden loss of power steering fluid.

Campaign page2021 Jayco Greyhawk

An inadequate connection between the power steering pressure line and the brake Hydroboost unit may result in a sudden loss of power steering fluid.

Campaign page2021 Jayco Greyhawk

The mounting brackets for the leveling system hydraulic pump and reservoir may fail, allowing the components to contact the ground.

Campaign page2021 Jayco Greyhawk

The heating, ventilation, and air conditioning (HVAC) blower motor circuit may be inadequate, which can allow the wiring harness to overheat.

Campaign page2021 Jayco Melbourne

The instrument cluster may fail to display any information when the vehicle is started.

Campaign page2021 Jayco Melbourne

The guide bushing on the parking pawl may fatigue, which can cause the parking pawl not to engage and result in a vehicle rollaway.

Campaign page2021 Jayco Melbourne

The shim on the torsion bar was incorrectly installed between the nut and the torsion bar, rather than between the ball stud and the torsion bar.

Campaign page2021 Jayco Melbourne

The wiring harnesses for the front seats may have been routed incorrectly and could become jammed and damaged in the swivel seat frames.

Campaign page2021 Jayco Melbourne

The rear part of the fender liner on the front axle may contact and chafe the brake hose, possibly resulting in a loss of brake fluid.

Campaign page2021 Jayco Melbourne

The Operator's Manual may not contain the correct information about how the automatic parking function ("Auto-P") operates.

Campaign page2021 Jayco Melbourne

The heating, ventilation, and air conditioning (HVAC) blower motor circuit may be inadequate, which can allow the wiring harness to overheat.

Campaign page2021 Jayco Melbourne Prestige

The instrument cluster may fail to display any information when the vehicle is started.

Campaign page2021 Jayco Melbourne Prestige

The guide bushing on the parking pawl may fatigue, which can cause the parking pawl not to engage and result in a vehicle rollaway.

Campaign page2021 Jayco Melbourne Prestige

The shim on the torsion bar was incorrectly installed between the nut and the torsion bar, rather than between the ball stud and the torsion bar.

Campaign page2021 Jayco Melbourne Prestige

The wiring harnesses for the front seats may have been routed incorrectly and could become jammed and damaged in the swivel seat frames.

Campaign page2021 Jayco Melbourne Prestige

The rear part of the fender liner on the front axle may contact and chafe the brake hose, possibly resulting in a loss of brake fluid.

Campaign page2021 Jayco Melbourne Prestige

The Operator's Manual may not contain the correct information about how the automatic parking function ("Auto-P") operates.

Campaign page2021 Jayco Melbourne Prestige

The certification labels may have the incorrect tire size information, causing the operator to install incorrect tires.

Campaign page2021 Jayco Northpoint

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Jayco Northpoint

Due to a manufacturing issue, the tires may experience a belt separation.

Campaign page2021 Jayco Northpoint

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Jayco Northpoint

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Jayco Northpoint

The welds on the axle spindle may fail, causing the wheel/spindle assembly to break away from the axle tube.

Campaign page2021 Jayco Northpoint

The rear stabilizer bar attachment brackets may break and separate from the vehicle.

Campaign page2021 Jayco Precept

The heat shield beneath the storage compartment may not be long enough, which can allow the heat from the exhaust system to melt the storage compartment.

Campaign page2021 Jayco Precept

The engine covers may not contain sufficient heat insulation, causing the interior surface temperatures to be excessive.

Campaign page2021 Jayco Precept

The bedlift motor may fail due to internal gear failure, causing the overhead bunk bed to release from the stowed position.

Campaign page2021 Jayco Precept

An inadequate connection between the power steering pressure line and the brake hydroboost unit may result in a sudden loss of power steering fluid.

Campaign page2021 Jayco Redhawk

An inadequate connection between the power steering pressure line and the brake Hydroboost unit may result in a sudden loss of power steering fluid.

Campaign page2021 Jayco Redhawk

The mounting brackets for the leveling system hydraulic pump and reservoir may fail, allowing the components to contact the ground.

Campaign page2021 Jayco Redhawk

The windshield wipers may fail, resulting in reduced driver visibility.

Campaign page2021 Jayco Seneca

The tire valve stem extension for the inner wheel may come into contact with the outer wheel rim opening and become damaged.

Campaign page2021 Jayco Seneca

The steering arm and tie rod bolts may have a defective seam that can fracture.

Campaign page2021 Jayco Seneca

The tie rod clamps may be loose, which could result in loose tie rod ends that could break or detach.

Campaign page2021 Jayco Seneca

The windshield wipers may fail, resulting in reduced driver visibility.

Campaign page2021 Jayco Seneca Prestige

The tire valve stem extension for the inner wheel may come into contact with the outer wheel rim opening and become damaged.

Campaign page2021 Jayco Seneca Prestige

The steering arm and tie rod bolts may have a defective seam that can fracture.

Campaign page2021 Jayco Seneca Prestige

The tie rod clamps may be loose, which could result in loose tie rod ends that could break or detach.

Campaign page2021 Jayco Seneca Prestige

The hydraulic leveling leg foot pads may become loose and separate from the vehicle.

Campaign page2021 Keystone Alpine

The backer board behind the cabinet for the wardrobe may not have been installed during production.

Campaign page2021 Keystone Arcadia

The hydraulic leveling leg foot pads may become loose and separate from the vehicle.

Campaign page2021 Keystone Avalanche

The solar controller may be incorrectly wired, causing certain components and safety alarms, such as carbon monoxide and propane gas detectors, to become inoperable.

Campaign page2021 Keystone Bullet

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Keystone Bullet

The bedroom emergency egress window may have an incorrect crank handle installed.

Campaign page2021 Keystone Bullet

The fuel station controller may fail.

Campaign page2021 Keystone Carbon

Improper clearance may allow the tires to contact the outrigger, causing damage to the tires.

Campaign page2021 Keystone Cougar

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Keystone Cougar

The frame rails do not have enough cross support, which could cause them to buckle under certain side-load stress conditions.

Campaign page2021 Keystone Cougar

The inverter may have been incorrectly wired, causing power to energize the shore power connection, when in use.

Campaign page2021 Keystone Cougar

The Solar Prep wiring to the 12VDC breakers located by the battery may not be connected to the protected side of the breaker.

Campaign page2021 Keystone Cougar

The inverter may have been incorrectly wired, causing power to energize the shore power connection, when in use.

Campaign page2021 Keystone Cougar

The interior range cooktop is installed in a cabinet that may not be entirely sealed from the furnace cavity. As a result, during furnace operation, the interior range cooktop burner flame may invert.

Campaign page2021 Keystone Cougar

The U-bolts on these axles may have been improperly torqued, causing the bolts to loosen and the axle to slide.

Campaign page2021 Keystone Crossroads Redwood

The fuel station controller may fail.

Campaign page2021 Keystone Fuzion

The hydraulic leveling leg foot pads may become loose and separate from the vehicle.

Campaign page2021 Keystone Fuzion

The auxiliary fuel supply tank mounting straps may have been improperly secured with grade 2 bolts instead of grade 5 bolts.

Campaign page2021 Keystone Fuzion

The generator transfer switch may be incorrectly wired with the transfer switch "Line" wiring (shore cord) and "Load" wiring (power center wiring) reversed, allowing the generator power to energize the shore power connection.

Campaign page2021 Keystone Fuzion

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Keystone Hideout

The LED backlight circuit board in the cooktop range may fail, causing the board to overheat.

Campaign page2021 Keystone Montana

Due to a manufacturing issue, the tires may experience a belt separation.

Campaign page2021 Keystone Montana

The LED backlight circuit board in the cooktop range may fail, causing the board to overheat.

Campaign page2021 Keystone Montana High Country

The 120VAC wiring connectors for the slide room circuit were not mounted properly, which can allow water to enter the electrical connections.

Campaign page2021 Keystone Montana High Country

A section of the frame rail may have inadequate support where the draw bar is attached, allowing the frame rail to buckle.

Campaign page2021 Keystone Outback

The Federal Identification Tag incorrectly states that the tire pressure should be 65 PSI, when the correct tire pressure is 80 PSI. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification."

Campaign page2021 Keystone Outback

The fuel station controller may fail.

Campaign page2021 Keystone Raptor

Due to a manufacturing issue, the tires may experience a belt separation.

Campaign page2021 Keystone Raptor

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 Keystone Springdale

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 KZ Durango

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 KZ Durango

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 KZ Durango Gold

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 KZ Durango Gold

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 KZ Sonic

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 KZ Sonic

The microwave circuits were improperly connected to a 20amp circuit breaker instead of a 15amp circuit breaker.

Campaign page2021 KZ Sonic

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 KZ Sportsmen

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 KZ Sportsmen

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 KZ Sportsmen Le

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 KZ Sporttrek

The water heater circuits were wired with an incorrect size circuit breaker, which may prevent the breaker from tripping, and failing to provide adequate wiring protection.

Campaign page2021 KZ Sporttrek

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 KZ Spree

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 KZ Stratus

The regulator may fail, causing an increase in propane pressure.

Campaign page2021 KZ Stratus

The water heater circuits were wired with an incorrect size circuit breaker, which may prevent the breaker from tripping, and failing to provide adequate wiring protection.

Campaign page2021 KZ Stratus

In certain stove serial number ranges, a gas leak may occur in the cooking stove.

Campaign page2021 Lance Travel Trailer

In certain stove serial number ranges, a gas leak may occur in the cooking stove.

Campaign page2021 Lance Travel Trailer

The hood stops mounting adhesive may fail, which can allow the hood stop to detach while the vehicle is in transit.

Campaign page2021 Newmar Bay Star

The seat belt brackets for the dinette seat belts were modified to avoid interference with the vehicle slide-out rollers in the floor. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 210, "Seat belt Assembly Anchorages" and 207, "Seating Systems."

Campaign page2021 Newmar Bay Star

The entry door latch may fail and not allow entry or exit.

Campaign page2021 Newmar Bay Star

The service valves on the LPG tanks may be improperly connected, which can cause a propane leak.

Campaign page2021 Newmar Bay Star

The wiring under the seats may be incorrectly secured, which can lead to a pinched wire in the seat adjustment mechanism and cause an electrical short circuit.

Campaign page2021 Newmar Bay Star

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Newmar Bay Star

The hood stops mounting adhesive may fail, which can allow the hood stop to detach while the vehicle is in transit.

Campaign page2021 Newmar Bay Star Sport

The seat belt brackets for the dinette seat belts were modified to avoid interference with the vehicle slide-out rollers in the floor. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 210, "Seat belt Assembly Anchorages" and 207, "Seating Systems."

Campaign page2021 Newmar Bay Star Sport

The wiring under the seats may be incorrectly secured, which can lead to a pinched wire in the seat adjustment mechanism and cause an electrical short circuit.

Campaign page2021 Newmar Bay Star Sport

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Newmar Bay Star Sport

The stove's saddle valve securing bolt may be overtightened, possibly damaging the o-ring seal and causing a continuous gas leak.

Campaign page2021 Newmar Bay Star Sport

The wiring under the seats may be incorrectly secured, which can lead to a pinched wire in the seat adjustment mechanism and cause an electrical short circuit.

Campaign page2021 Newmar Dutch Star

The upper bolt connecting the steering column may not have been properly tightened, causing the nut to loosen off the bolt, potentially resulting in loss of steering control.

Campaign page2021 Newmar Dutch Star

The instrument cluster may intermittently go blank while the vehicle is in motion.

Campaign page2021 Newmar Dutch Star

A fuel leak may occur from the fuel hose between the fuel pump and the remote fuel filter head.

Campaign page2021 Newmar Dutch Star

A fuel leak may occur from the fuel hose between the fuel pump and the remote fuel filter head.

Campaign page2021 Newmar Dutch Star

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Newmar Dutch Star

The sealing washer may not seat correctly in the pilot boreholes, allowing the high-pressure fuel rail assembly to leak.

Campaign page2021 Newmar Dutch Star

The sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak.

Campaign page2021 Newmar Dutch Star

The steering output shaft may be too short and could disengage from the steering input shaft.

Campaign page2021 Newmar Dutch Star

The adjustable brake pedal assembly may be missing a return spring. This may cause the brake lights to stay illuminated after the brake pedal is released.

Campaign page2021 Newmar Dutch Star

The steering gear mounting bolts may become loose and back out, resulting in difficulty steering.

Campaign page2021 Newmar Dutch Star

The brake light switch may chafe against the windshield wiper mechanism, which could damage the brake light switch or it's wiring, and cause the brake lights to not illuminate.

Campaign page2021 Newmar Dutch Star

The front leveling jacks may not be fastened correctly to the chassis, possibly causing the jacks to fail to support the weight of the motorhome.

Campaign page2021 Newmar Dutch Star

The upper bolt connecting the steering column may not have been properly tightened, causing the nut to loosen off the bolt, potentially resulting in loss of steering control.

Campaign page2021 Newmar Essex

A machining defect may cause pressure to build in the power steering pump and break the shaft seal, resulting in a loss of power steering assist.

Campaign page2021 Newmar Essex

The instrument cluster may intermittently go blank while the vehicle is in motion.

Campaign page2021 Newmar Essex

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Newmar Essex

The steering gear mounting bolts may become loose and back out, resulting in difficulty steering.

Campaign page2021 Newmar Essex

The front leveling jacks may not be fastened correctly to the chassis, possibly causing the jacks to fail to support the weight of the motorhome.

Campaign page2021 Newmar Essex

The wiring under the seats may be incorrectly secured, which can lead to a pinched wire in the seat adjustment mechanism and cause an electrical short circuit.

Campaign page2021 Newmar Kountry Star

The upper bolt connecting the steering column may not have been properly tightened, causing the nut to loosen off the bolt, potentially resulting in loss of steering control.

Campaign page2021 Newmar Kountry Star

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Newmar Kountry Star

The tie rod clamps may be loose, which could result in loose tie rod ends that could break or detach.

Campaign page2021 Newmar Kountry Star

The brake light switch may chafe against the windshield wiper mechanism, which could damage the brake light switch or it's wiring, and cause the brake lights to not illuminate.

Campaign page2021 Newmar Kountry Star

One of the six brake caliper mounting bolts on the driver side steer axle may have been incorrectly tightened.

Campaign page2021 Newmar Kountry Star

The upper bolt connecting the steering column may not have been properly tightened, causing the nut to loosen off the bolt, potentially resulting in loss of steering control.

Campaign page2021 Newmar London Aire

A machining defect may cause pressure to build in the power steering pump and break the shaft seal, resulting in a loss of power steering assist.

Campaign page2021 Newmar London Aire

The instrument cluster may intermittently go blank while the vehicle is in motion.

Campaign page2021 Newmar London Aire

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Newmar London Aire

The steering output shaft may be too short and could disengage from the steering input shaft.

Campaign page2021 Newmar London Aire

The steering gear mounting bolts may become loose and back out, resulting in difficulty steering.

Campaign page2021 Newmar London Aire

The front leveling jacks may not be fastened correctly to the chassis, possibly causing the jacks to fail to support the weight of the motorhome.

Campaign page2021 Newmar London Aire

The wiring under the seats may be incorrectly secured, which can lead to a pinched wire in the seat adjustment mechanism and cause an electrical short circuit.

Campaign page2021 Newmar New Aire

The upper bolt connecting the steering column may not have been properly tightened, causing the nut to loosen off the bolt, potentially resulting in loss of steering control.

Campaign page2021 Newmar New Aire

The instrument cluster may intermittently go blank while the vehicle is in motion.

Campaign page2021 Newmar New Aire

A fuel leak may occur from the fuel hose between the fuel pump and the remote fuel filter head.

Campaign page2021 Newmar New Aire

A fuel leak may occur from the fuel hose between the fuel pump and the remote fuel filter head.

Campaign page2021 Newmar New Aire

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Newmar New Aire

The sealing washer may not seat correctly in the pilot boreholes, allowing the high-pressure fuel rail assembly to leak.

Campaign page2021 Newmar New Aire

The sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak.

Campaign page2021 Newmar New Aire

The steering output shaft may be too short and could disengage from the steering input shaft.

Campaign page2021 Newmar New Aire

The adjustable brake pedal assembly may be missing a return spring. This may cause the brake lights to stay illuminated after the brake pedal is released.

Campaign page2021 Newmar New Aire

The wiring under the seats may be incorrectly secured, which can lead to a pinched wire in the seat adjustment mechanism and cause an electrical short circuit.

Campaign page2021 Newmar Ventana

The upper bolt connecting the steering column may not have been properly tightened, causing the nut to loosen off the bolt, potentially resulting in loss of steering control.

Campaign page2021 Newmar Ventana

The instrument cluster may intermittently go blank while the vehicle is in motion.

Campaign page2021 Newmar Ventana

A fuel leak may occur from the fuel hose between the fuel pump and the remote fuel filter head.

Campaign page2021 Newmar Ventana

A fuel leak may occur from the fuel hose between the fuel pump and the remote fuel filter head.

Campaign page2021 Newmar Ventana

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Newmar Ventana

The tie rod clamps may be loose, which could result in loose tie rod ends that could break or detach.

Campaign page2021 Newmar Ventana

The sealing washer may not seat correctly in the pilot boreholes, allowing the high-pressure fuel rail assembly to leak.

Campaign page2021 Newmar Ventana

The sealing washer may not seat correctly in the pilot bore holes, allowing the high pressure fuel rail assembly to leak.

Campaign page2021 Newmar Ventana

The steering output shaft may be too short and could disengage from the steering input shaft.

Campaign page2021 Newmar Ventana

The adjustable brake pedal assembly may be missing a return spring. This may cause the brake lights to stay illuminated after the brake pedal is released.

Campaign page2021 Newmar Ventana

One of the six brake caliper mounting bolts on the driver side steer axle may have been incorrectly tightened.

Campaign page2021 Newmar Ventana

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Palomino Puma

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Prime Time Crusader

Due to a manufacturing issue, the tires may experience a belt separation.

Campaign page2021 Prime Time Crusader

The steering column control module may cause the driver's side air bag not to deploy as intended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."

Campaign page2021 Ram 2500

An electrical short may occur in the heater grid relay with the ignition on or off.

Campaign page2021 Ram 2500

The tailgate may not latch properly due to misaligned tailgate strikers, which could result in the tailgate opening while driving.

Campaign page2021 Ram 2500

A build-up of pressure and heat inside the transmission may result in a transmission fluid leak from the dipstick tube.

Campaign page2021 Ram 2500

The ABS control module software may prevent the electronic stability control (ESC) malfunction indicator light from illuminating during certain conditions. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 126, "Electronic Stability Control Systems."

Campaign page2021 Ram 2500

The side air bag inflatable curtain (SABIC) assemblies may have been manufactured with the incorrect amount of compressed gas, which can result in an improper air bag deployment.

Campaign page2021 Ram 2500

An electrical short in the relay may cause a vehicle fire with the ignition on or off.

Campaign page2021 Ram 2500

An electrical short may occur in the Solid State Intake Heater Grid Relay, which could result in a vehicle fire.

Campaign page2021 Ram 2500

The steering column control module may cause the driver's side air bag not to deploy as intended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."

Campaign page2021 Ram 3500

An electrical short may occur in the heater grid relay with the ignition on or off.

Campaign page2021 Ram 3500

The tailgate may not latch properly due to misaligned tailgate strikers, which could result in the tailgate opening while driving.

Campaign page2021 Ram 3500

A build-up of pressure and heat inside the transmission may result in a transmission fluid leak from the dipstick tube.

Campaign page2021 Ram 3500

The ABS control module software may prevent the electronic stability control (ESC) malfunction indicator light from illuminating during certain conditions. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 126, "Electronic Stability Control Systems."

Campaign page2021 Ram 3500

The side air bag inflatable curtain (SABIC) assemblies may have been manufactured with the incorrect amount of compressed gas, which can result in an improper air bag deployment.

Campaign page2021 Ram 3500

An electrical short in the relay may cause a vehicle fire with the ignition on or off.

Campaign page2021 Ram 3500

Incorrect information in the Service and Owner's Manuals may cause the flanged lug nuts to be over-tightened, which could result in a broken wheel stud and possible wheel separation.

Campaign page2021 Ram 3500

An electrical short may occur in the Solid State Intake Heater Grid Relay, which could result in a vehicle fire.

Campaign page2021 Ram 3500

The adhesive bond between the glass and the metal hinge frame of the frameless windows may fail which would then allow the glass to detach and fall out.

Campaign page2021 Thor Motor Coach Ace

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Thor Motor Coach Aria

The tire valve stem extension for the inner wheel may contact the outer wheel rim opening and become damaged.

Campaign page2021 Thor Motor Coach Aria

The heat shield between the LP tank and chassis muffler was not installed.

Campaign page2021 Thor Motor Coach Axis

The BIM (Battery Isolation Manager)/BIR (Battery Isolation Relay) is not watertight when exposed to engine compartment heat.

Campaign page2021 Thor Motor Coach Chateau

Bolts of the wrong size were used to secure the barrel chair pedestals, allowing the pedestal to separate from the floor in the event of a crash. As such, these motorhomes fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 207, "Seating Systems" and number 210, "Seat Belt Assembly Anchorages."

Campaign page2021 Thor Motor Coach Chateau

The wiring harnesses for the front seats may have been routed incorrectly and could become jammed and damaged in the swivel seat frames.

Campaign page2021 Thor Motor Coach Chateau

The battery cable may not have been properly secured within the chassis rail, which can cause it to contact the exhaust manifold and heat shield.

Campaign page2021 Thor Motor Coach Chateau

A wire harness in the rear of the vehicle may contact the vehicle frame, resulting in damage to the circuits that support the fuel pump and the anti-lock braking system (ABS).

Campaign page2021 Thor Motor Coach Chateau

The wiring harnesses for the front seats may have been routed incorrectly and could become jammed and damaged in the swivel seat frames.

Campaign page2021 Thor Motor Coach Delano

The saddle valve securing bolt may be overtightened, possibly damaging the o-ring seal and causing a continuous gas leak.

Campaign page2021 Thor Motor Coach Four Winds

The BIM (Battery Isolation Manager)/BIR (Battery Isolation Relay) is not watertight when exposed to engine compartment heat.

Campaign page2021 Thor Motor Coach Four Winds

Bolts of the wrong size were used to secure the barrel chair pedestals, allowing the pedestal to separate from the floor in the event of a crash. As such, these motorhomes fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 207, "Seating Systems" and number 210, "Seat Belt Assembly Anchorages."

Campaign page2021 Thor Motor Coach Four Winds

The wiring harnesses for the front seats may have been routed incorrectly and could become jammed and damaged in the swivel seat frames.

Campaign page2021 Thor Motor Coach Four Winds

A 100amp converter breaker was incorrectly installed at the battery tray when a 70amp breaker is required, possibly resulting in the wiring connected to the breaker overheating.

Campaign page2021 Thor Motor Coach Four Winds

The battery cable may not have been properly secured within the chassis rail, which can cause it to contact the exhaust manifold and heat shield.

Campaign page2021 Thor Motor Coach Four Winds

The adhesive bond between the glass and the metal hinge frame of the frameless windows may fail which would then allow the glass to detach and fall out.

Campaign page2021 Thor Motor Coach Four Winds

A wire harness in the rear of the vehicle may contact the vehicle frame, resulting in damage to the circuits that support the fuel pump and the anti-lock braking system (ABS).

Campaign page2021 Thor Motor Coach Four Winds

The rear axle differential may have an insufficient amount of fluid, possibly resulting in a failure of the rear axle assembly and a driveshaft separation.

Campaign page2021 Thor Motor Coach Four Winds

The driver and front passenger overhead cabinets may detach.

Campaign page2021 Thor Motor Coach Hurricane

The electronic control center circuit board may be damaged from voltages over 17 volts causing damage to the circuit board.

Campaign page2021 Thor Motor Coach Hurricane

The LP gas line may have been incorrectly routed through the rear suspension leaf springs, which could damage the line and cause a gas leak.

Campaign page2021 Thor Motor Coach Magnitude

The LP gas line may have been incorrectly routed through the rear suspension leaf springs, which could damage the line and cause a gas leak.

Campaign page2021 Thor Motor Coach Magnitude

The LP gas line may have been incorrectly routed through the rear suspension leaf springs, which could damage the line and cause a gas leak.

Campaign page2021 Thor Motor Coach Omni

The LP gas line may have been incorrectly routed through the rear suspension leaf springs, which could damage the line and cause a gas leak.

Campaign page2021 Thor Motor Coach Omni

The adhesive that bonds the vented portion of the window may fail.

Campaign page2021 Thor Motor Coach Outlaw

The solar panel frame may fracture around the mounting bolts, allowing the panel to detach from the vehicle.

Campaign page2021 Thor Motor Coach Rize

The fuel hose between the inline fuel filter and the injection pump module (IPM) may have inadequate clamp force, possibly resulting in a gasoline leak.

Campaign page2021 Thor Motor Coach Rize

The retractable awning may extend unintentionally during transit.

Campaign page2021 Thor Motor Coach Rize

The solar panel frame may fracture around the mounting bolts, allowing the panel to detach from the vehicle.

Campaign page2021 Thor Motor Coach Scope

The fuel hose between the inline fuel filter and the injection pump module (IPM) may have inadequate clamp force, possibly resulting in a gasoline leak.

Campaign page2021 Thor Motor Coach Scope

The retractable awning may extend unintentionally during transit.

Campaign page2021 Thor Motor Coach Scope

The fuel hose between the inline fuel filter and the injection pump module (IPM) may have inadequate clamp force, possibly resulting in a gasoline leak.

Campaign page2021 Thor Motor Coach Sequence

The dinette booth seat belts may be too short preventing them from being usable by some occupants. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) numbers 208, "Occupant Crash Protection" and 209, "Seat Belt Assemblies."

Campaign page2021 Thor Motor Coach Sequence

The fuel hose between the inline fuel filter and the injection pump module (IPM) may have inadequate clamp force, possibly resulting in a gasoline leak.

Campaign page2021 Thor Motor Coach Tellaro

The dinette booth seat belts may be too short preventing them from being usable by some occupants. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) numbers 208, "Occupant Crash Protection" and 209, "Seat Belt Assemblies."

Campaign page2021 Thor Motor Coach Tellaro

The transmission shifter cable may separate and disconnect from the transmission, causing the vehicle to not perform shifts intended by the driver and the gear shift lever position not matching the actual transmission gear.

Campaign page2021 Thor Motor Coach Tellaro

The heat shield between the LP tank and chassis muffler was not installed.

Campaign page2021 Thor Motor Coach Vegas

The driver and front passenger overhead cabinets may detach.

Campaign page2021 Thor Motor Coach Windsport

The electronic control center circuit board may be damaged from voltages over 17 volts causing damage to the circuit board.

Campaign page2021 Thor Motor Coach Windsport

The output line on the LPG tanks may not connect properly to the service valve, which can cause a propane leak.

Campaign page2021 Tiffin Allegro

The slide-room may extend out 6 to 8 inches while parked or possibly while moving, due to defective seals in the hydraulic cylinders.

Campaign page2021 Tiffin Allegro

The buss bar may be improperly secured, which can cause electrical components in the DC Distribution Panel to overheat.

Campaign page2021 Tiffin Allegro

The sofa seat belts may not have been installed correctly, which could result in unsecured passengers. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 210, "Seat Belt Assembly Anchorages."

Campaign page2021 Tiffin Allegro

A fuel leak may occur from the fuel hose between the fuel pump and remote filter head.

Campaign page2021 Tiffin Allegro

The condensation pan under the refrigerator may overflow and leak into the Molex electrical connections on the floor.

Campaign page2021 Tiffin Allegro Breeze

The output line on the LPG tanks may not connect properly to the service valve, which can cause a propane leak.

Campaign page2021 Tiffin Allegro Breeze

The buss bar may be improperly secured, which can cause electrical components in the DC Distribution Panel to overheat.

Campaign page2021 Tiffin Allegro Breeze

The sofa seat belts may not have been installed correctly, which could result in unsecured passengers. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 210, "Seat Belt Assembly Anchorages."

Campaign page2021 Tiffin Allegro Breeze

The output line on the LPG tanks may not connect properly to the service valve, which can cause a propane leak.

Campaign page2021 Tiffin Allegro Red

The patio awning may have been improperly installed, allowing it to detach.

Campaign page2021 Tiffin Allegro Red

The sofa seat belts may not have been installed correctly, which could result in unsecured passengers. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 210, "Seat Belt Assembly Anchorages."

Campaign page2021 Tiffin Allegro Red

The output line on the LPG tanks may not connect properly to the service valve, which can cause a propane leak.

Campaign page2021 Tiffin Phaeton

The sofa seat belts may not have been installed correctly, which could result in unsecured passengers. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 210, "Seat Belt Assembly Anchorages."

Campaign page2021 Tiffin Phaeton

During manufacturing, an electrical outlet was not installed as intended, resulting in an open electrical wire inside the wall.

Campaign page2021 Tiffin Phaeton

A fuel leak may occur from the fuel hose between the fuel pump and remote filter head.

Campaign page2021 Tiffin Phaeton

The sealing washer may not seat correctly in the pilot bore, allowing the high pressure fuel rail assembly to leak.

Campaign page2021 Tiffin Phaeton

A roof mounted body panel may have been improperly attached to the roof.

Campaign page2021 Tiffin Phaeton

The valve stem stabilizer can become loose, allowing the valve stem extender to contact the wheel.

Campaign page2021 Tiffin Phaeton

The rear-center holding tank water pan bolts may pull through the lip of the pan, allowing the tank to drop down onto the exhaust pipe.

Campaign page2021 Tiffin Wayfarer

Continuous stress on the frame rail hitch extensions may cause them to fail.

Campaign page2021 Tiffin Wayfarer

Interference from the rear ladder can prevent the rear egress window from fully opening.

Campaign page2021 Vanleigh Beacon

The water heater housing may not have been properly sealed, allowing gas to enter the coach.

Campaign page2021 Vanleigh Beacon

The water heater housing may not have been properly sealed, allowing gas to enter the coach.

Campaign page2021 Vanleigh Vilano

The front turn signals may have a smaller than required luminous lens area. As such these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 108, "Lamps, Reflective Devices, and Associated Equipment."

Campaign page2021 Winnebago Adventurer

The hood bracket adhesive may have been incorrectly applied which can allow the bracket to detach.

Campaign page2021 Winnebago Adventurer

The power bed motor may experience an internal gear failure, causing the bed to extend prior to the safety strap engaging.

Campaign page2021 Winnebago Adventurer

The solar charging system was incorrectly designed without sufficient over-current protection, which can allow the circuit to overheat and melt the fuse.

Campaign page2021 Winnebago Ekko

The blind spot monitoring system may fail without warning to the driver.

Campaign page2021 Winnebago Ekko

The 12-Volt charging system may have improperly routed wires and loose electrical connections, which can overload the electrical circuits and cause damage to electrical components, including the auxiliary alternator.

Campaign page2021 Winnebago Ekko

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Winnebago Ekko

The seat belt retractors may lock up when the vehicle is on a slight incline. As such, these seats fail to comply with the requirements of Federal Motor Vehicle Safety Standards numbers 208, "Occupant Crash Protection" and 209, "Seat Belt Assemblies."

Campaign page2021 Winnebago Ekko

The hood bracket adhesive may have been incorrectly applied which can allow the bracket to detach.

Campaign page2021 Winnebago Forza

The turn signals may have a smaller than required luminous lens area. As such these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 108, "Lamps, Reflective Devices, and Associated Equipment."

Campaign page2021 Winnebago Forza

The spare tire carrier may fail when loaded with a certain off-road style tire.

Campaign page2021 Winnebago Micro Minnie

The cast aluminum pull handles on the cabinet doors and drawers may have sharp edges.

Campaign page2021 Winnebago Micro Minnie

The quick disconnect fittings in the LP gas system may be cracked, causing a gas leak.

Campaign page2021 Winnebago Micro Minnie

These trailers were built with undersized axles that may not support the weight of the vehicle and could break.

Campaign page2021 Winnebago Micro Minnie

The rear roof cap aerofence trim may become loose and detach during transit.

Campaign page2021 Winnebago Navion

The door assembly may have been manufactured with incorrect window adhesion, causing the window to loosen or detached.

Campaign page2021 Winnebago Navion

Supplemental Restraint System (SRS) wires can be caught in the seat mechanism when the driver or passenger seats are adjusted.

Campaign page2021 Winnebago Navion

The retractable awning may extend unintentionally during transit.

Campaign page2021 Winnebago Navion

An incorrect hitch label was installed, which can lead to overloading of the vehicle.

Campaign page2021 Winnebago Navion

The LP fuel line is routed near the rear wheel well, which may allow the fuel line to contact the tire and become damaged, resulting in a gas leak.

Campaign page2021 Winnebago Navion

Supplemental Restraint System (SRS) wires can be caught in the seat mechanism when the driver or passenger seats are adjusted.

Campaign page2021 Winnebago Revel

The cables near the lithium batteries may contact the battery hold-down brackets, which can damage the cables and cause a short circuit.

Campaign page2021 Winnebago Revel

The retractable awning may extend unintentionally during transit.

Campaign page2021 Winnebago Revel

The power bed motor may experience an internal gear failure, causing the bed to extend prior to the safety strap engaging.

Campaign page2021 Winnebago Revel

These motorhomes have an auxiliary alternator belt that may wear and detach.

Campaign page2021 Winnebago Revel

The fuel hose between the fuel filter and Injection Pump Module (IPM) may not be properly secured, which can cause a gas leak.

Campaign page2021 Winnebago Solis

The internal aluminum burner tubes that connect to the gas valves may fracture and cause a gas leak.

Campaign page2021 Winnebago Solis

The seat belt retractors may lock up when the vehicle is on a slight incline. As such, these seats fail to comply with the requirements of Federal Motor Vehicle Safety Standards numbers 208, "Occupant Crash Protection" and 209, "Seat Belt Assemblies."

Campaign page2021 Winnebago Solis

The retractable awning may extend unintentionally during transit.

Campaign page2021 Winnebago Travato

The fuel hose between the fuel filter and Injection Pump Module (IPM) may not be properly secured, which can cause a gas leak.

Campaign page2021 Winnebago Travato

The internal aluminum burner tubes that connect to the gas valves may fracture and cause a gas leak.

Campaign page2021 Winnebago Travato

The retractable awning may extend unintentionally during transit.

Campaign page2021 Winnebago Travato

The wire harness may have been built incorrectly, resulting in the loss of over-current protection.

Campaign page2021 Winnebago Travato

The seat belt retractors may lock up when the vehicle is on a slight incline. As such, these seats fail to comply with the requirements of Federal Motor Vehicle Safety Standards numbers 208, "Occupant Crash Protection" and 209, "Seat Belt Assemblies."

Campaign page2021 Winnebago Travato

The rear roof cap aerofence trim may become loose and detach during transit.

Campaign page2021 Winnebago View

The door assembly may have been manufactured with incorrect window adhesion, causing the window to loosen or detached.

Campaign page2021 Winnebago View

Supplemental Restraint System (SRS) wires can be caught in the seat mechanism when the driver or passenger seats are adjusted.

Campaign page2021 Winnebago View

The retractable awning may extend unintentionally during transit.

Campaign page2021 Winnebago View

An incorrect hitch label was installed, which can lead to overloading of the vehicle.

Campaign page2021 Winnebago View

The LP fuel line is routed near the rear wheel well, which may allow the fuel line to contact the tire and become damaged, resulting in a gas leak.

Campaign page2021 Winnebago View

The retractable awning may extend unintentionally during transit.

Campaign page2021 Winnebago View